Your specialist in diesel technology
No vehicle selected Select make, model and engine

Loading...
F
Select engine / type

Enter a UK registration number to find matching vehicles from our shop inventory.

S
Selected vehicle
Show matching parts
Vehicle search Select make, model and engine
Loading...
  1. 1 Make
  2. 2 Model
  3. 3 Engine / type
F
Select engine / type

Enter a UK registration number to find matching vehicles from our shop inventory.

P0201, P0202, P0203, P0204: injector circuit cylinder 1–4 – causes, diagnosis and fixes

DieselFix Neuss |

The engine suddenly runs rough, shakes at idle and has hardly any power – and the fault memory shows P0201, P0202, P0203 or P0204. The engine control unit is reporting a problem in the electrical circuit of a specific injector. The good news: the cause is often not the injector itself but a connector or a wire.

What do P0201 to P0204 mean?

P0201 / P0202 / P0203 / P0204 – Injector circuit/open – cylinder 1 / 2 / 3 / 4
When driving the injector of the named cylinder, the engine control unit detects an electrical fault, typically an open circuit or an implausible current in the control line.

The last digit is the cylinder number. P0200 is the general injector circuit code without a specific cylinder; five- and six-cylinder engines add P0205 and P0206. Solenoid and piezo injectors are affected alike.

Note: the meaning is defined by the OBD-II standard; some manufacturers add their own sub-codes. Always read the complete fault memory including the freeze-frame data.

Typical symptoms

  • Rough running and shaking, especially at idle
  • Noticeable loss of power or limp mode
  • Misfire codes (e.g. P0300–P0304) stored as well
  • Engine warning light, sometimes a flashing glow plug light

The most common causes

CauseHow to check itNote
Loose or corroded injector connector, broken locking tabUnplug it, check the pins for corrosion and spread terminalsCheapest and most common cause
Oil in the connector (leaking valve cover gasket or injector seal)Check connector and cable for oil, fix the leak, clean the contactsOil wicks into the cable and disturbs the contact
Chafed or broken wiring harness (e.g. under the valve cover)Wiggle test, measure continuity and insulation from the ECU connector to the injectorOn some engines the injector wiring runs under the valve cover
Faulty injector coil (solenoid) or piezo elementMeasure resistance and compare with the other injectors or manufacturer data; swap testIf the fault follows the injector, the injector is faulty
Faulty driver stage in the ECUOnly once wiring and injector are fine; check the drive signal with an oscilloscopeRare, often the result of a short circuit

Step-by-step diagnosis

  1. Read the fault memory, note the freeze frame and check whether the fault is active or intermittent. Caution: injectors are driven with high voltage – only unplug connectors with the ignition off.
  2. Visual check: connector, locking tab and wiring at the affected cylinder, oil in the connector, chafe points on the harness.
  3. Measure the injector resistance and compare it with the others. Solenoid injectors typically have a very low coil resistance; piezo injectors have different values – use the manufacturer data. A clearly different or infinite reading is suspicious.
  4. Check the wiring from the ECU to the injector for continuity and shorts to ground while moving the harness (wiggle test).
  5. Swap test: swap the injector with a neighbouring cylinder (new seals, update the coding). If the code moves with it (e.g. from P0202 to P0203), the injector is faulty. If it stays on the same cylinder, the cause is wiring, connector or ECU.
  6. More on electrical fault finding: Electrical problems with injectors.

Can I keep driving with P0201–P0204?

Only briefly and gently: the affected cylinder is not firing or only intermittently, the engine runs rough and may stall. Drive to the garage without high load. Background on misfires: Diesel misfire diagnosis.

If the injector is the cause

If the fault follows the injector in the swap test, or its resistance is clearly out of range, replacement is the only fix. Remanufactured and new injectors by vehicle: Injectors. Whether to replace one or the whole set: Single or full-set replacement. Then code the injector: Injector coding. More test methods: Testing a diesel injector.

Frequently asked questions

Does P0201 always mean the injector is faulty?

No. The connector, corrosion, oil in the connector or a chafed wire are often to blame. The injector is only definitely faulty if the code follows it in the swap test.

What is the difference between P0200 and P0201?

P0200 reports a general injector circuit fault. P0201 to P0204 also name the affected cylinder.

Do I need to recode after a swap test?

On many engines yes, because the injector correction values are assigned to a cylinder. After swapping, assign the codes to the new positions.

Leave a comment

Please note: comments must be approved before they are published.

Delivery country

Prices and refundable deposits depend on the delivery country. Your language selection stays unchanged.